Quince líneas centradas en el proceso, una fábrica: elija una categoría para comparar modelos, especificaciones y plazos de entrega.
A terminal crimping machine deforms the terminal barrel around the stripped strands so the joint carries current and resists pull-out. Crimp quality is set by the applicator or die, the crimp height relative to the terminal's window, and the pull force the finished joint withstands — not by press force alone. This is the family entry point and covers both feeding methods and both automation tiers: loose-terminal presses for low volume, banded and reel feed for automatic work, single-head and double-head configurations. Dies and applicators are machined on our own CNC vertical machining centres, so proprietary terminal series can usually be tooled. Send your terminal and we crimp and measure it before you commit.
185 modelos
A splice in a harsh environment may need three things at once: a mechanical crimp to carry the load, solder to make the electrical joint permanent, and a seal to keep moisture out of the strands. Doing them on one machine avoids re-heating a joint that has already been crimped, which is where these assemblies most often fail. The process steps are sequenced and the heat input is controlled, because the solder stage sits next to insulation that must not be damaged. Specify the splice type, the conductor cross-section and the environmental requirement. This is a joint-specific machine: the tooling follows the splice, and a sample splice is run before shipment.
5 modelos
Cutting and stripping is the first operation on any harness line: the wire is measured, cut to length, and its insulation removed at one or both ends. This page is the entry point to the family, covering general-purpose machines for single-core and multi-core wire, from bench-top pneumatic units through programmable cut-strip models that hold cut-length tolerance to ± 0.4 %. Start here if you are replacing hand tools or adding your first automatic cut-and-strip stage. If the cable has a braid, a jacket or a gauge above 120 mm² (AWG 8-0000), go to the coaxial, jacket or busbar pages instead. Every machine is run-in tested before shipment.
252 modelos
Taping and bundling is the stage that turns a set of terminated wires into a harness: tape fixes the branches along their length, and a tie closes the bundle so it holds its shape. It is the operation most often still done by hand, and the one where labour cost concentrates on a harness line. This page opens the family and covers taping and bundling heads from handheld units through bench-top machines to in-line stations. The first specification to fix is the wrap pattern, because full wrap, point wrap and spiral are different heads and the pattern is set by the harness drawing rather than by preference. Pitch consistency is the quality figure worth asking for.
80 modelos
Winding and tying takes a finished cable and turns it into a shippable coil: the cable is wound into a defined shape — circle, small circle, or figure-of-eight — and secured with a tie at fixed points. Figure-of-eight is used where a plain coil would introduce a twist that the cable must not carry. The machine is sized by coil outer diameter, cable diameter and coil weight, and the tie count per coil. Winding speed is almost never the constraint; what matters is that every coil comes out the same shape, because a coil that varies is a packaging problem at the customer's end. Desktop and upright versions are available. This line also covers cutting, winding and tying in one machine.
25 modelos
Inserting the sleeve and shrinking it are two operations, and between them the sleeve sits loose on the splice — where it can be displaced, dropped, or fitted on the wrong side of a connector. Machines on this page insert and bake in one cycle so the sleeve is never a loose part in the process. This matters most on short splices where the sleeve has little to grip before shrinking. The specification inputs are the tube inner diameter and shrink ratio, the sleeve length, and the splice geometry. Insulation that sits inside the shrinking zone has to be checked against the dwell temperature, because overheating it is a defect that appears weeks after shipment, not during assembly.
13 modelos
Tightening a connector nut or a cable gland is a fastening operation, not a termination: the joint is already made and what remains is torque. Doing it by hand produces a torque spread that shows up later as either a loose seal or a cracked housing, and the machine exists to hold one torque across a shift. The variables are the thread size, the torque required and the access geometry around the connector — the last is usually what decides the tooling, because a nut inside a moulded housing has less clearance than the drawing suggests. Where the assembly also needs waterproofing, the sequence of nut and seal relative to the crimp has to be fixed first.
8 modelos
Turing es uno de los principales fabricantes y proveedores de moldes y accesorios de China; a lo largo de los años, hemos establecido buenas relaciones con nuestros clientes para el negocio mayorista de otros productos.
73 modelos
Heat shrink baking shrinks a sleeve onto a splice or terminal so it seals the joint and relieves strain. The variable that decides quality is not the oven temperature by itself but the combination of set temperature, dwell time and airflow: a sleeve can look fully shrunk on the surface while the adhesive at the splice has never reached its activation temperature. Ovens come in enclosed, semi-closed, overhead and infrared forms, and the harness geometry usually picks the form — a long assembly that cannot be placed inside a chamber needs an overhead or infrared head. Confirm the tubing specification first; the machine holds a temperature, it does not choose one.
23 modelos
Every machine upstream in the line depends on how the wire arrives at it. A pay-off stand holds the reel and releases the wire at controlled tension; without that control the wire either drags and stretches or feeds slack and tangles, and both show up as length errors at the cutting machine rather than as a problem at the stand. The range covers passive release frames and powered unwinding reels for heavier or larger-diameter cable. The sizing inputs are reel size and weight, wire diameter and the line speed the stand must support. The English naming of this line is being re-verified; give us the reel specification on your enquiry and we will size the stand to it.
5 modelos
Busbar and heavy solid conductor are the heavy-gauge end of the family. The insulation is a coating or a wound sleeve rather than an extruded jacket, and the conductor is solid, so the cut is a peeling action against a rigid body instead of a blade closing on strands. Two facts decide the machine: the bar cross-section and whether it is flat, round or formed, and the insulation type, because a coating that adheres to copper behaves differently from a sleeved bar. This is a small, specialised product line whose English name is currently being re-verified against search demand; describe your application on the enquiry and we will confirm which configuration applies.
3 modelos
A nylon cable tie is the cheapest way to close a bundle, which is why it is still applied by hand on most lines — and why the machine earns its place: it tightens every tie to the same tension and cuts the tail flush, so the finished bundle neither crushes the wires nor leaves a tail that cuts the installer. The range covers handheld units that follow the operator along a long branch, and desktop units for short repeated branches. The sizing inputs are tie width and length, bundle diameter, and the loop tension your wiring can tolerate. Our handheld unit takes 3.6 × 200 mm ties and runs on 0.2 kW at AC 220 V. Tie material and length are confirmed against your bundle before ordering.
17 modelos
Ultrasonic welding joins stranded copper to stranded copper, or wire to a terminal or busbar, without solder, flux or filler metal. A sonotrode presses the strands together while oscillating at ultrasonic frequency, and the strands bond to each other in the solid state. The result is a joint with no third metal in it and no heat-affected zone, which is why it appears where a crimped splice would introduce a dissimilar material or where the joint will see thermal cycling. Weld quality is judged on two measurements together — pull force and cross-section — because a joint can pass pull test while the section shows an incomplete bond. Tooling follows the joint geometry.
11 modelos
Flat cable, insulating paper, tape and formed insulation components are cut to length and punched in the same pass — a hole, a notch or a locating feature that a guillotine alone cannot produce. The process is closer to a press operation than to wire cutting: the sizing inputs are the material thickness, the tooling geometry and the total force the punch needs, and the cut quality is judged on burr height rather than on length tolerance. If your part is cut only and carries no hole or notch, the tape cutting machines are the better match. Tooling is made to your drawing, and a first-article sample is run before shipment.
1 modelo
Hot-dip tinning closes a stranded end: the wire is fluxed and dipped in molten solder so the strands are locked together. It is used ahead of screw clamps and soldered joints, where bare strands would spread and unwind under torque, and on multi-core cable where the ends must be held together to be inserted. The process variables belong to your downstream process, not to the machine — solder alloy, flux type and bath temperature are set by what happens to the joint afterwards. The range covers standalone tinning machines and multi-core and double-head versions. Note the distinction from crimp-and-dip machines: those apply a terminal as well, these do not.
2 modelos
A shielded cable carries a braided mesh that has to be separated from the dielectric, brushed or combed to remove stray strands, turned back or cut to length, and dressed so it can be terminated without shorting the conductor. Done by hand this is slow and it is where shield fragments end up inside the joint. Machines on this page perform those mesh operations in a controlled cycle with consistent length. The specification inputs are the braid construction — material, coverage percentage, wire diameter — and the cable construction beneath it, because brushing depth is set relative to the dielectric and over-brushing damages it. We run a length of your cable before shipment.
6 modelos
Welding a splice and then inserting it into a housing are normally two stations, and the gap between them is where the strands get disturbed: a welded bundle handled as a loose part can be spread or bent before the housing locks it. This machine welds and inserts in one automatic cycle, so the joint goes from the anvil straight into the housing without being picked up. Specifying it needs three things: the bundle cross-section, the weld area, and the housing part number with its cavity layout. Because the tooling follows both the splice and the housing, a change in either is a tooling change. A sample bundle and housing are run before shipment.
1 modelo
A thermal protector has to be welded into a harness without heating the bimetal inside it, which is what makes this a distinct machine rather than a general welder: the weld is made by ultrasonic energy precisely because it does not conduct heat into the part. Operation runs at 850 pcs/h on AWG16#–AWG26# copper wire, with vibratory bowl feeding and multi-stage inspection rejection, so a part that fails the check is removed from the flow rather than passing to the next station. The specification inputs are the protector part number, the wire gauge and the required weld area. Because the component is the constraint, we weld your protector and your wire and return a cross-section before the order is confirmed.
3 modelosIdeal para líneas combinadas de corte-pelado-crimpado que crimpan dos extremos de cable en un terminal
Ideal para cables de alimentación y cables de nueva energía, 10-120 mm2
Ideal para el agrupado de gran volumen de bridas de nylon enlazadas de 3.6 x 200 mm: la alimentación automática reduce el trabajo manual de carga de bridas y el control digital de la tensión mantiene uniforme cada agrupado.
Ideal para el engarzado de ambos extremos de cables redondos con cubierta, con manguito de tubo e inserción en la carcasa.
Cuatro razones medibles — cada afirmación a continuación es una capacidad documentada, no material de marketing.
Las cuchillas accionadas por servomotor mantienen la longitud de la tira dentro de 0,1 mm: cortes limpios, sin mellas y repetibles lote tras lote.
Especificaciones reales: rendimiento, rango de alambres y velocidades de ciclo en cada ficha técnica, y cada máquina se prueba al 100 % en funcionamiento antes del envío.
Matrices y aplicadores fabricados según el plano de su terminal: utillaje JIS/ISO, ajuste confirmado antes de que se envíe la máquina.
Garantía de 12 meses, repuestos originales en todo el mundo y asistencia remota con respuesta en 24 horas.
Ensamblado y sometido a control de calidad en nuestra planta de QingxiTuringnex es el fabricante: diseño, I+D, ensamblaje, pruebas de rodaje y control de calidad internos; sin intermediarios ni revendedores.
Automatización del procesamiento de cables para el ensamblaje de arneses en ocho industrias finales: máquinas dimensionadas y equipadas para la aplicación.
Comience por la industria a la que presta servicio, la máquina que necesita o el proceso que desea perfeccionar: cada camino conduce a la configuración adecuada.
Doce momentos reales de exposiciones, visitas a fábricas y reuniones con clientes en muchos países. Las máquinas que ve en este sitio funcionan en líneas de producción reales: cada máquina que enviamos se fabrica, se prueba y se instala para un cliente real.
Los nombres de los clientes, los datos de los casos y las citas se comparten con permiso por escrito; no hay testimonios de relleno en este sitio.
Fotos tomadas en las plantas de producción de los clientes.
Elcab fabrica mazos de cables y conjuntos de cables en Turquía. Estas fotos son de su planta de producción, donde una máquina manual de bridas para cables de nailon Turingnex funciona con la herramienta manual alimentada desde una unidad de sobremesa.
Máquina manual para bridas de nylonLas aplicaciones que equipamos y los pasos del proceso que normalmente necesitan una máquina. Pídanos referencias en su mercado.
Terminales de alta variedad para distintos modelos de vehículos, donde la trazabilidad del engaste y los registros de auditoría son importantes.
Producciones de lotes pequeños con cambios frecuentes entre calibres de alambre.
Cable HV de gran sección transversal: calidad del pelado e integridad del aislamiento.
Líneas multiproceso — corte, pelado, engarzado y prueba — con matrices y repuestos disponibles en stock.
Un ingeniero acompaña su proyecto desde la muestra de material hasta la línea puesta en marcha, sin centros de llamadas ni transferencias.
Comparta su rango de cables, terminales y producción objetivo — un ingeniero, no un centro de llamadas.
Envíe su material. Realizamos una prueba gratuita de crimpado/pelado y le enviamos un video antes de que se comprometa.
Parámetros exactos, precio y plazo de entrega confirmados por escrito en un plazo de 24 horas.
Orientación para la configuración, repuestos y asistencia remota después de la entrega.
Garantía, repuestos, puesta en marcha y asistencia remota: la máquina sigue generando ingresos después de la factura.
Cobertura garantizada para cada máquina fabricada, con repuestos originales enviados a todo el mundo.
Configuración asistida por un ingeniero a la llegada, con capacitación del operador incluida en su pedido.
Diagnósticos y recorridos de configuración por videollamada — sin esperar cadenas de correos electrónicos.
Manuales del operador, fichas técnicas y tutoriales en vídeo en inglés técnico y claro.
Marcos de selección, conocimientos prácticos de mantenimiento y tendencias del sector: escritos para talleres de arneses, no para motores de búsqueda.
Peladoras neumáticas de sobremesa, peladoras informáticas de uno y dos extremos, y máquinas para pelar y enrollar cables de gran calibre: elija la familia que se adapte a su rango de cables, lote y acabado.
Leer la guía
La calidad del engarce se desvía antes de fallar. Una rutina sencilla diaria-semanal-mensual para prensas de banco y máquinas automáticas mantiene estable la altura de engarce.
Leer la guía
La alimentación, la soldadura de modo dual, los datos de fuerza del servomotor y la integración de la inserción son las cuatro tendencias que están cambiando las líneas de arneses: qué esperar de las máquinas.
Leer la guíaMOQ, plazo de entrega, pago, envío y moldes: las preguntas que todo comprador hace primero.
Envíe su rango de cables, terminales y producción objetivo. Un ingeniero responderá con la cotización, las herramientas y el plazo de entrega.